Description | The bq2010 Gas Gauge IC is intended for battery-pack or in-system installation to maintain an accurate record of a battery's available charge. The IC monitors a voltage drop across a sense resistor connected in series between the negative battery terminal and ground to determine charge and discharge... |
Features |
➤ Conservative and repeatable measurement of available charge in rechargeable batteries
➤ Designed for battery pack integration
- 120µA typical standby current
- Small size enables imple-
mentations
in
as
little
as
1 2
square inch of PCB
➤ Integrate within a system or as a stand-alone device
- Display capacity via single-
wire serial communication
port or direct drive of LEDs
➤ Measurements compensated for current and temperature
➤ Self-discharge compensation using internal temperature sensor
➤ Accurate measurements across a wide range of current (> 500:1)
➤ 16-pin narrow SOIC...
|
Datasheet | BQ2010 Datasheet - 1.02MB |
Part Number | Description |
---|---|
Texas Instruments |
Programmable Multi-Chemistry Fast-Charge Management The bq2000 is a programmable, monolithic IC for fast-charge management of nickel cadmium (NiCd), nickel metal-hydride (NiMH), or lithium-ion (Li-Ion) batteries in single- or multi-chemistry applications. The bq2000 chooses the proper battery chemistry (either nickel or lithium) and proceeds with the optimal charging and termination algorithms. This process eliminates undesirable, undercharged, or overcharged conditions, and allows accurate and safe termination of fast charge Depending on the chemistry, the bq2000 provides a number of charge termination criteria: • Peak voltage, PVD (for NiCd and NiMH) • Minimum charge current (for Li-Ion) • Maximum temperature • Maximum charge time For sa... |
Texas Instruments |
Programmable Multi-Chemistry Fast-Charge Management The bq2000T is a programmable, monolithic IC for fast-charge management of nickel cadmium (NiCd), nickel metal-hydride (NiMH), or lithium-ion (Li-Ion) batteries in single- or multi-chemistry applications. The bq2000T chooses the proper battery chemistry (either nickel or lithium) and proceeds with the optimal charging and termination algorithms. This process eliminates undesirable, undercharged, or overcharged conditions, and allows accurate and safe termination of fast charge. Depending on the chemistry, the bq2000T provides a number of charge termination criteria: • Rate of temperature rise (ΔT/Δt) (for NiCd and NiMH) • Minimum charge current (for Li-Ion) • Maximum temperature • Maximum ... |
Power-One |
60...132 Watt DC-DC Converters Q Series 60...132 Watt DC-DC Converters Input voltage ranges up to 168 V DC 1 or 2 isolated outputs 3.3...48 V DC 3 kV AC I/O electric strengh test voltage LGA • Extremely slim case (4TE wide), fully enclosed • Extremely low inrush current, hot swappable • Operating ambient temperaturerange –40...71 °C with convection cooling Selection chart Output 1 Uo nom Io nom [V DC] [A] 5.1 16 12 8 15 6.6 24 4 24 4.4 30 3.3 48 2.2 5.1 7.5 12 4 15 3.3 24 2.2 Io max [A] 16 8 6.6 4 4.4 3.3 2.2 7.5 4 3.3 2.2 Output 2 Uo nom Io nom [V DC] [A] 5.1 7.5 12 4 15 3.3 24 2.2 Output 2 Uo nom Io nom Io max [V DC] [A] [A] 5.1 7.5 9.5 12 4 5 15 3.3 4 24 2.2 2.75 Io max [A] 7.5 4 3.3 2.2 Type Input Voltage 16...... |
Benchmarq |
NiCd/NiMH Fast-Charge Management The bq2002 and bq2002/F Fast-Charge ICs are low-cost CMOS battery-charge controllers providing reliable charge termination for both NiCd and NiMH battery applications. Controlling a current-limited or constant-current supply allows the bq2002/F to be the basis for a cost-effective stand-alone or system-integrated charger. The bq2002/F integrates fast charge with optional top-off and pulsed-trickle control in a single IC for charging one or more NiCd or NiMH battery cells. Fast charge is initiated on application of the charging supply or battery replacement. For safety, fast charge is inhibited if the battery temperature and voltage are outside configured limits. Fast charge is terminated by... |
UNITRODE |
NiCd/NiMH Fast-Charge Management The bq2002C Fast-Charge IC is a lowcost CMOS battery-charge controller providing reliable charge termination for both NiCd and NiMH battery applications. Controlling a current-limited or constant-current supply allows the bq2002C to be the basis for a costeffective stand-alone or system-integrated charger. The bq2002C integrates fast charge with pulsed-trickle control in a single IC for charging one or more NiCd or NiMH battery cells. Fast charge is initiated on application of the charging supply or battery replacement. For safety, fast charge is inhibited if the battery temperature and voltage are outside configured limits. Fast charge is terminated by any of the following: n Peak voltage ... |
Benchmarq |
NiCd/NiMH Fast-Charge Management The bq2002D/T Fast-Charge IC are low-cost CMOS battery-charge controllers able to provide reliable charge termination for both NiCd and NiMH battery applications. Controlling a current-limited or constant-current supply allows the bq2002D/T to be the basis for a cost-effective stand-alone or system-integrated charger. The bq2002D/T integrates fast charge with optional top-off and pulsed-trickle control in a single IC for charging one or more NiCd or NiMH battery cells. Fast charge is initiated on application of the charging supply or battery replacement. For safety, fast charge is inhibited if the battery temperature and voltage are outside configured limits. Pin Names Fast charge is termin... |
UNITRODE |
NiCd/NiMH Fast-Charge Management The bq2002E and bq2002G FastCharge ICs are low-cost CMOS battery-charge controllers providing reliable charge termination for both NiCd and NiMH battery applications. Controlling a current-limited or constant-current supply allows the bq2002E/G to be the basis for a costeffective stand-alone or system-integrated charger. The bq2002E/G integrates fast charge with optional top-off and pulsed- trickle control in a single IC for charging one or more NiCd or NiMH battery cells. Fast charge is initiated on application of the charging supply or battery replacement. For safety, fast charge is inhibited if the battery temperature and voltage are outside configured limits. Pin Names Fast charge is te... |
Benchmarq |
NiCd/NiMH Fast-Charge Management The bq2002 and bq2002/F Fast-Charge ICs are low-cost CMOS battery-charge controllers providing reliable charge termination for both NiCd and NiMH battery applications. Controlling a current-limited or constant-current supply allows the bq2002/F to be the basis for a cost-effective stand-alone or system-integrated charger. The bq2002/F integrates fast charge with optional top-off and pulsed-trickle control in a single IC for charging one or more NiCd or NiMH battery cells. Fast charge is initiated on application of the charging supply or battery replacement. For safety, fast charge is inhibited if the battery temperature and voltage are outside configured limits. Fast charge is terminated by... |
UNITRODE |
NiCd/NiMH Fast-Charge Management The bq2002E and bq2002G FastCharge ICs are low-cost CMOS battery-charge controllers providing reliable charge termination for both NiCd and NiMH battery applications. Controlling a current-limited or constant-current supply allows the bq2002E/G to be the basis for a costeffective stand-alone or system-integrated charger. The bq2002E/G integrates fast charge with optional top-off and pulsed- trickle control in a single IC for charging one or more NiCd or NiMH battery cells. Fast charge is initiated on application of the charging supply or battery replacement. For safety, fast charge is inhibited if the battery temperature and voltage are outside configured limits. Pin Names Fast charge is te... |
Benchmarq |
Fast Chargeer The bq2003 Fast Charge IC provides comprehensive fast charge control functions together with high-speed switching power control circuitry on a monolithic CMOS device. Integration of closed-loop current control circuitry allows the bq2003 to be the basis of a cost-effective solution for stand-alone and systemintegrated chargers for batteries of one or more cells. Switch-activated discharge-beforecharge allows bq2003-based chargers to support battery conditioning and capacity determination. High-efficiency power conversion is accomplished using the bq2003 as a hysteretic PWM controller for switch-mode regulation of the charging current. The bq2003 may alternatively be used to gate an externall... |
Benchmarq |
Fast Chargeer The bq2004 Fast Charge IC provides comprehensive fast charge control functions together with high-speed switching power control circuitry on a monolithic CMOS device. Integration of closed-loop current control circuitry allows the bq2004 to be the basis of a cost-effective solution for stand-alone and systemintegrated chargers for batteries of one or more cells. Switch-activated discharge-beforecharge allows bq2004-based chargers to support battery conditioning and capacity determination. High-efficiency power conversion is accomplished using the bq2004 as a hysteretic PWM controller for switch-mode regulation of the charging current. The bq2004 may alternatively be used to gate an externall... |
Benchmarq |
Fast Chargeer The bq2004E and bq2004H Fast Charge ICs provide comprehensive fast charge control functions together with high-speed switching power control circuitry on a monolithic CMOS device. Integration of closed-loop current control circuitry allows the bq2004 to be the basis of a cost-effective solution for stand-alone and systemintegrated chargers for batteries of one or more cells. Switch-activated discharge-beforecharge allows bq2004E/H-based chargers to support battery conditioning and capacity determination. High-efficiency power conversion is accomplished using the bq2004E/H as a hysteretic PWM controller for switch-mode regulation of the charging current. The bq2004E/H may alternatively be use... |
Benchmarq |
Fast Chargeer The bq2004E and bq2004H Fast Charge ICs provide comprehensive fast charge control functions together with high-speed switching power control circuitry on a monolithic CMOS device. Integration of closed-loop current control circuitry allows the bq2004 to be the basis of a cost-effective solution for stand-alone and systemintegrated chargers for batteries of one or more cells. Switch-activated discharge-beforecharge allows bq2004E/H-based chargers to support battery conditioning and capacity determination. High-efficiency power conversion is accomplished using the bq2004E/H as a hysteretic PWM controller for switch-mode regulation of the charging current. The bq2004E/H may alternatively be use... |
Benchmarq |
Fast Chargeer The bq2005 Fast-Charge IC provides comprehensive fast charge control functions together with high-speed switching power control circuitry on a monolithic CMOS device for sequential charge man age ment in dual battery packapplications. In te gra tion of closed-loop cur rent control circuitry allows the bq2005 to be the basis of a cost-effective solution for stand-alone and sys tem-integrated charg ers for bat ter ies of one or more cells. Switch-activated dis-charge-before-charge allows bq2005-based chargers to support battery conditioning and capacity determ-i nation. High-efficiency power con ver sion is accomplished using the bq2005 as a hysteretic PWM controller for switch-mode regulation... |
Texas Instruments |
Fast-Charge IC The bq2007 is a highly integrated monolithic CMOS IC designed to provide intelligent battery charging and charge status monitoring for standalone charge systems. The bq2007 provides a wide variety of charge status display formats. The bq2007 internal charge status monitor supports up to a seven-segment bar graph or a single BCD digit display. The bar graph display indicates up to seven monotonic steps, whereas the BCD digit counts in ten steps of 10% increments. The bq2007 output drivers can direct-drive either an LCD or LED display. Charge action begins either by application of the charging supply or by replacement of the battery pack. For safety, charging is inhibited until battery tempera... |
UNITRODE |
Gas Gauge IC The bq2011 Gas Gauge IC is intended for battery-pack installation to maintain an accurate record of available battery charge. The IC monitors a voltage drop across a sense resistor connected in series between the negative battery terminal and ground to determine charge and discharge activity of the battery. The bq2011 is designed for systems such as power tools with very high discharge rates. Battery self-discharge is estimated based on an internal timer and temperature sensor. Compensations for battery temperature and rate of charge or discharge are applied to the charge, discharge, and selfdischarge calculations to provide available charge information across a wide range of operating condi... |