| Description | The AD9225 is a monolithic, single-supply, 12-bit, 25 MSPS analog-to-digital converter with an on-chip, high performance sample-and-hold amplifier and voltage reference. The AD9225 uses a multistage differential pipelined architecture with output error correction logic to provide 12-bit accuracy at ... |
| Features |
Monolithic 12-Bit, 25 MSPS ADC Low Power Dissipation: 280 mW Single 5 V Supply No Missing Codes Guaranteed Differential Nonlinearity Error: ؎0.4 LSB Complete On-Chip Sample-and-Hold Amplifier and
Voltage Reference Signal-to-Noise and Distortion Ratio: 71 dB Spurious-Free Dynamic Range: –85 dB Out-of-Range Indicator Straight Binary Output Data 28-Lead SOIC 28-Lead SSOP Compatible with 3 V Logic Complete 12-Bit, 25 MSPS Monolithic A/D Converter AD9225 FUNCTIONAL BLOCK DIAGRAM VINA VINB CAPT CAPB VREF SENSE SHA CLK AVDD DRVDD MDAC1 GAIN = 16 5 ADC 5 MDAC2 GAIN = 4 MDAC3 GAIN = 4 3 ADC ... |
| Datasheet |
 AD9225 Datasheet - 1.01MB |
| Part Number | Description |
|---|---|
 Analog Devices |
CMOS A/D Converter The AD9200 is a monolithic, single supply, 10-bit, 20 MSPS analog-to-digital converter with an on-chip sample-and-hold amplifier and voltage reference. The AD9200 uses a multistage differential pipeline architecture at 20 MSPS data rates and guarantees no missing codes over the full operating temperature range. The input of the AD9200 has been designed to ease the development of both imaging and communications systems. The user can select a variety of input ranges and offsets and can drive the input either single-ended or differentially. The sample-... |
Analog Devices |
Dual Channel/ 20 MHz 10-Bit Resolution CMOS ADC PRODUCT HIGHLIGHTS The AD9201 is a complete dual channel, 20 MSPS, 10-bit CMOS ADC. The AD9201 is optimized specifically for applications where close matching between two ADCs is required (e.g., I/Q channels in communications applications). The 20 MHz sampling rate and wide input bandwidth will cover both narrowband and spread-spectrum channels. The AD9201 integrates two 10-bit, 20 MSPS ADCs, two input buffer amplifiers, an internal voltage reference and multiplexed digital output buffers. Each ADC incorporates a simultaneous sampling sample-andhold amplifier at its input. The analog inputs are buffered; no external input buffer op amp will be required in most applications. The ADCs are im... |
Analog Devices |
A/D Converter The AD9203 is a monolithic low power, single supply, 10-bit, 40 MSPS analog-to-digital converter, with an on-chip voltage reference. The AD9203 uses a multistage differential pipeline architecture and guarantees no missing codes over the full operating temperature range. Its input range may be adjusted between 1 V and 2 V p-p. The AD9203 has an onboard programmable reference. An external reference can also be chosen to suit the dc accuracy and temperature drift requirements of an application. An external resistor can be used to reduce power consumption when operating at lower sampling rates. This yields power savings for users who do not require the maximum sample rate. This feature is espec... |
Analog Devices |
1.8V Dual Analog-to-Digital Converter ......................................................................... 3 Specifications..................................................................................... 4 DC Specifications ......................................................................... 4 AC Specifications.......................................................................... 5 Digital Specifications ................................................................... 6 Switching Specifications .............................................................. 7 Timing Specifications .................................................................. 8 Absolute Maximum Ratings....................................... |
Analog Devices |
JESD204B/JESD204C Dual ADC The AD9207 is a dual, 12-bit, 6 GSPS analog-to-digital converter (ADC). The ADC input features an on-chip wideband buffer with overload protection. This device is designed to support applications capable of direct sampling wideband signals up to 8 GHz. An onchip, low phase noise, phase-locked loop (PLL) clock synthesizer is available to generate the ADC sampling clock, which simplifies the printed circuit board (PCB) distribution of a high frequency clock signal. A clock output buffer is available to transmit the ADC sampling clock to other devices. The dual ADC cores have code error rates (CER) better than 2 × 10−15. Low latency fast detection and signal monitoring are available for automat... |
Analog Devices |
Dual Analog-to-Digital Converter ......................................................................... 4 Specifications..................................................................................... 5 DC Specifications ......................................................................... 5 AC Specifications.......................................................................... 6 Digital Specifications ................................................................... 7 Switching Specifications .............................................................. 9 Timing Specifications ................................................................ 10 Absolute Maximum Ratings................................. |
Analog Devices |
1.8 V Analog-to-Digital Converter 10-Bit, 200 MSPS/250 MSPS/300 MSPS, 1.8 V Analog-to-Digital Converter AD9211 06041-001 FEATURES SNR = 60.1 dBFS @ fIN up to 70 MHz @ 300 MSPS ENOB of 9.7 @ fIN up to 70 MHz @ 300 MSPS (−1.0 dBFS) SFDR = −80 dBc @ fIN up to 70 MHz @ 300 MSPS (−1.0 dBFS) Excellent linearity DNL = ±0.1 LSB typical INL = ±0.2 LSB typical LVDS at 300 MSPS (ANSI-644 levels) 700 MHz full power analog bandwidth On-chip reference, no external decoupling required Integrated input buffer and track-and-hold Low power dissipation 437 mW @ 300 MSPS—LVDS SDR mode 410 mW @ 300 MSPS—LVDS DDR mode Programmable input voltage range 1.0 V to 1.5 V, 1.25 V nominal 1.8 V analog and digital supply operation Selectable output data... |
Analog Devices |
Serial LVDS A/D Converter Th... |
Analog Devices |
RF Analog-to-Digital Converter The AD9213 is a single, 12-bit, 6 GSPS/10.25 GSPS, radio frequency (RF) analog-to-digital converter (ADC) with a 6.5 GHz input bandwidth. The AD9213 supports high dynamic range frequency and time domain applications requiring wide instantaneous bandwidth and low conversion error rates (CER). The AD9213 features a 16-lane JESD204B interface to support maximum bandwidth capability. The AD9213 achieves dynamic range and linearity performance while consuming <4.6 W typical. The device is based on an interleaved pipeline architecture and features a proprietary calibration and randomization technique that suppresses interleaving spurious artifacts into its noise floor. The linearity performance o... |
Analog Devices |
RF Analog-to-Digital Converter The AD9213S-CSH is a single, 12-bit, 10.25 GSPS, RF analogto-digital converter (ADC) with a 6.5 GHz input bandwidth. The AD9213S-CSH supports high dynamic range frequency and time domain applications requiring wide instantaneous bandwidth and low conversion error rates (CERs). The AD9213S-CSH features a 16-lane JESD204B interface to support maximum bandwidth capability. The AD9213S-CSH achieves dynamic range and linearity performance while consuming <4.6 W typical. The device is based on an interleaved pipeline architecture and features a proprietary calibration and randomization technique that suppresses interleaving spurious artifacts into its noise floor. The linearity performance of the ... |
Analog Devices |
3V A/D Converter The AD9214 is a 10-bit monolithic sampling analog-to-digital converter (ADC) with an on-chip track-and-hold circuit, and is optimized for low cost, low power, small size, and ease of use. The product operates up to 105 MSPS convers... |
Analog Devices |
3V A/D Converter The AD9215 is a family of monolithic, single 3 V supply, 10-bit, 65/80/105 MSPS analog-to-digital converters (ADC). This family features a high performance sample-and-hold amplifier (SHA) and voltage reference. The AD9215 uses a multistage differential pipelined architecture with output error correction logic to provide 10-bit accuracy at 105 MSPS data rates and to guarantee no missing codes over the ... |
Analog Devices |
Dual A/D Converter The AD9216 is a dual, 3 V, 10-bit, 105 MSPS analog-to-digital converter (ADC). It features dual high performance sampleand-hold amplifiers (SHAs) and an integrated voltage reference. The AD9216 uses a multistage differential pipelined architecture with output error correction logic to provide 10-bit accuracy and guarantee no missing codes over the full operating temperature range at up to 105 MSPS data rates. The wide bandwidth, differential SHA allows for a variety of user selectable input ranges and offsets, including single-ended applications. The AD9216 is suitable for various applications, including multiplexed systems that switch full-scale voltage levels in successive channels and for... |
Analog Devices |
3V Dual Analog-to-Digital Converter The AD9218 is a dual 10-bit monolithic sampling analog-to-digital converter with on-chip track-and-hold circuits. The product is low cost, low power, and is small and easy to use. The AD9218 operates at a 105 MSPS conversion rate with outstanding dynamic performance over its full operating range. Each channel can be operated independently. The ADC requires only a single 3.0 V (2.7 V to 3.6 V) power supply and a clock for full operation. No external reference or driver components are required for many applications. The digital outputs are TTL/CMOS compatible and a separate output power supply pin supports interfacing with 3.3 V or 2.5 V logic. The clock input is TTL/CMOS compatible and the 10... |
Analog Devices |
40/65 MSPS Serial LVDS 1.8 V A/D Converter The AD9219 is a quad, 10-bit, 40/65 MSPS analog-to-digital converter (ADC) with an on-chip sample-and-hold circuit designed for low cost, low power, small size, and ease of use. The product operates at a conversion rate of up to 65 MSPS and is optimized for outstanding dynamic performance and low power in applications where a small package size is critical. The ADC requires a single 1.8 V power supply and LVPECL-/ CMOS-/LVDS-compatible sample rate clock for full performance operation. No external reference or driver components are required for many applications. Rev. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by An... |
Analog Devices |
Complete 12-Bit 1.5/3.0/10.0 MSPS Monolithic A/D Converters The AD9221, AD9223, and AD9220 are a generation of high performance, single supply 12-bit analog-to-digital converters. Each device exhibits true 12-bit linearity and temperature drift performance1 as well as 11.5-bit or better ac performance.2 The AD9221/AD9223/AD9220 share the same interface options, package, and pinout. Thus, the ... |
Analog Devices |
Monolithic A/D Converters The AD9221, AD9223, and AD9220 are a generation of high performance, single supply 12-bit analog-to-digital converters. Each device exhibits true 12-bit linearity and temperature drift performance1 as well as 11.5-bit or better ac performance.2 The AD9221/AD9223/AD9220 share the same interface options, package, and pinout. Thus, the ... |